Stick Arc Welder

MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask

MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask
MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask
MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask
MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask
MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask
MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask

MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask
Gas Shielded Welder 150A Semi-automated Medicinal Wire Portable Welding Machine. ACCORDING THE MACHINE TYPE USE POWER SUPPLY.

Check the connection of work piece, earth cable, welding torch, gas cylinder, regulator and hose, make sure they are firm and reliable. Switch on the power source. Turn on the gas valve, adjust gas volume to 3-5L/MIN. Check if there is gas leaking. Hold the torch and keep tip of Tungsten electrode 2-3 mm above the work piece, and tilt 20-30 to vertical direction.

Aim Tungsten electrode to the welding seam. Push torch switch, after arc is ignited, move the torch along seam evenly.

Fine tune the welding parameter to obtain exquisite welding seam. Release the torch switch to finish a welding cycle. After finish operation, turn off the gas valve, push torch switch to clear the residual gas in the regulator. At the end, turn off welding power source and wall switch. When using an open arc process, it is necessary to use correct eye, head, and body protection.

E02 Output control section is damaged or dead. E03 Did not give the driver board signal, but the actual voltage output. Welding machine should be installed in a stable position and with good. Avoid transport in invert or side. Connect electrode holder, earth cable, according to connection diagram.

Use 8 heat-resistant PVC hose connect the flow meter with the gas. Commission the machine after the machine is installed and tested.

MIG state when the function is Receiving arc voltage adjust. MMA state when the function is arc force adjust. Spot welding status, functions as spot welding time adjust. MIG state when the function is Receiving arc current adjust. MMA state when the function is welding current adjust.

Spot welding status, functions as spot welding interval adjust. MIG state when the function is electronic Inductor adjust.

MMA state when the function is invalid. Spot welding status, functions as electronic Inductor adjust.

No displayheader Fan does not rotateNo welding output. Confirmed air switch is closed. The input cable connected to an electric power source.

Fans turnNo error codeNo welding output. The inspection machine all kinds of patch cords is bad. The control circuit problem, find the cause, or contact your dealer. Ground off or not connected to the workpiece. Error code E01No welding output. May be overheating protection, wait 2-3 minutes to restore the machine to work. The temperature switch is broken. Using the welding current does not remain stable during.

Severe interference from the power grid or other electrical equipment. Welding current and welding voltage is too low or too high, you should adjust the suitable welding current and welding voltage. Welders must be equipped with welding mask, gloves and tie the sleeves and collar properly.

There should be an arc shield around welding field to protect others from arc shock. Do not weld near flammable, explosive materials or gases. Keep finger, hair and clothing away from the rotating fan. The power source must be grounded when welding. When yellow light is enlightened during welding, it is indicating that the welder is over current or over heat, and automatic protection will be triggered.

Stop welding immediately and wait until welder cool down. When welder is used for long time or big current, switch off the power after welder cool down. Do not switch off the welder during welding!

Welding machine should not work in a flammable and toxic environment, avoid moisture, rain, and do not directly expose to sun. Periodically maintain the machine and clean the dust inside.

Usually we use E-packet, sometimes DHL/EMS and other Excellent Service is used per customers' request. For those who are outside US. HK POST/SG POST/ DHL /EMS ect. It all depends on our customers' choices. Hope we can deal with soon and let us witness this moment.

We are Mrcartool, a professional automotive repair and maintain enterprise. Our own factory and chain repair shop located in China. We supply many products on Automobile consumer electronics, such as coder reader, diagnostic tool, GPS, DVR, bluetooth Car kit, injector cleaner and battery system tester etc. High product quality, reasonable prices, excellent customer service and a reliable credit standing is our target. Feedback is very important to us.

It is impossible to address issues if we do not know about them! The item "MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask" is in sale since Thursday, December 12, 2019. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\MIG Welders". The seller is "cardealmarket" and is located in Shenzhen. This item can be shipped worldwide.

  • Brand: Autool
  • MPN: Does Not Apply
  • Model: EWM528
  • Country/Region of Manufacture: China
  • Weight: 11.9kg
  • Size: 410*170*245mm
  • Future: Semi-automated and Medicinal Wire


MIG Welder Machine 110V MMA Stick ARC 3IN1 Combo Welder Flux Cored Wire WithMask